Search

Showing Posts Tagged Pinball, Repairs,
but not Game, Electronics
(Click any tag to remove it)
+ - Blog Post+ - Pinball+ - Project+ - P3+ - Game+ - Released+ - Archive+ - P1+ - Bally -35 OS+ - Custom ROM+ - Pinball+ - Stock Car+ - Arduino+ - Electronics+ - System 3-6 OS+ - + - Abandoned+ - Read Only+ - Repairs+ - Dracula+ - Cheetah+ - Hot Tip


System 6 MPU Repair Log

When I got it, it was a clean board that worked a few months ago. Game stopped booting, so owner had rom and 5101 sockets replaced. Repairer says board booted on bench (LEDs turned off), but when installed in game it still didn't reach attract mode.

  • I replaced the (still original) CPU and RAM (IC13 only) sockets, but that made no difference
  • Installed Leon's test rom (flashes LEDs without using RAM, etc), but it didn't boot either
  • Tried Andre's test rom (tests all chips without using RAM, etc), also didn't boot.
  • Checked all the inputs of the ROM and PIA chips with logic probe, none were stuck.
  • Replaced data line buffers (IC9+10) with jumpers in case they were a problem, but no difference.
  • Found out Andre's test rom also strobes A15 line along with LEDs (in case the PIA outputs or LED chip are broken), so I checked that but it also wasn't working. At this point I reason that the problem must be between the CPU and ROM (both known good).
  • Although all the address and data lines are strobing, it's still not working, so one must be strobing wrong somehow.
  • I write up a quick test rom comprising nothing but infinite loops, reasoning that this will keep the program counter (and thus the address lines since no other accesses are happening) constant. Installed in a known good board, it works as expected. Reading off the address lines one by one reports the address $7800, which is the first byte of the rom.
  • When installed in the problem board, A9-11 are low (as expected) but every line below them is strobing. I can't really explain this, why would the CPU be jumping all through a 512 byte subset of memory?
  • I Remove the remaining RAM (IC16) and PIA, but nothing changes
  • Since the data on the data lines should now be predictable (just reading the entry address, and then that address itself repeatedly), I reason that I should be able to pick it up with a logic analyzer. With mine hooked up to the 8 data lines, I record them at 24MHz (for overkill), and examine them, but I don't see any of that data. # - What I do note though is that at the beginning of the boot, D6 seems to wobble a bit while the rest don't. I don't know if that wobble is normal, but the one reliable thing about any pinball related troubleshooting, I've found, is that if there's 8 of a thing they tend to act the same, so I suspect something is up with the D6 line
  • I take out the CPU and rom, meaning that, per my look over the schematics, nothing should be attached to any of the data lines now (and thus they should all be floating), but when I apply power, I still read a signal on D6.
  • Something must be shorted somewhere, so I begin checking the resistance between D6 and every other signal on the board, eventually finding that it has continuity to A6. All that's left now is to actually find it
  • I begin at the source of D6 (IC9), and visually follow the trace all around the board, looking for any potential problems, but am unable to find any. Usually a short is between two adjacent pads of a chip, but looking at the various chips, none have A6 and D6 near each other. What I do realize though, is that the RAM chips have them directly across from each other. The chips are too wide to have a short that way, but the way these boards are routed with both chips next to each other, they squeezed the signals from the left side of the chip between the right side pads to reach the next chip over, which means the trace gets awfully close to the pads. To make matters worse, due to their cheap board manufacturing process, instead of masking off individual pads for soldering, they just did the whole strip of pads, which includes the traces running between the pads.
  • Although I'm unable to see a problem, this area seems suspect, so I desolder the sockets and confirm my theory: there's a tiny bit of solder bridging the pad of D6 to the A6 trace running next to it.
  • After removing the solder, the board boots fine

Posted Tuesday, April 17, 2018
at 11:31 PM


Tags: Blog Post, Pinball, Repairs,